add WiFiAccessPoint example

libraries/WiFi/examples/WiFiAccessPoint/WiFiAccessPoint.ino

@@ -0,0 +1,93 @@
+/*
+  WiFiAccessPoint.ino creates a WiFi access point and provides a web server on it.
+
+  Steps:
+  1. Connect to the access point "yourAp"
+  2. Point your web browser to http://192.168.4.1/H to turn the LED on or http://192.168.4.1/L to turn it off
+     OR
+     Run raw TCP "GET /H" and "GET /L" on PuTTY terminal with 192.168.4.1 as IP address and 80 as port
+
+  Created for arduino-esp32 on 04 July, 2018
+  by Elochukwu Ifediora (fedy0)
+*/
+
+#include <WiFi.h>
+#include <WiFiClient.h>
+#include <WiFiAP.h>
+
+#define LED_BUILTIN 2   // Set the GPIO pin where you connected your test LED or comment this line out if your dev board has a built-in LED
+
+// Set these to your desired credentials.
+const char *ssid = "yourAP";
+const char *password = "yourPassword";
+
+WiFiServer server(80);
+
+
+void setup() {
+  pinMode(LED_BUILTIN, OUTPUT);
+
+  Serial.begin(115200);
+  Serial.println();
+  Serial.println("Configuring access point...");
+
+  // You can remove the password parameter if you want the AP to be open.
+  WiFi.softAP(ssid, password);
+  IPAddress myIP = WiFi.softAPIP();
+  Serial.print("AP IP address: ");
+  Serial.println(myIP);
+  server.begin();
+
+  Serial.println("Server started");
+}
+
+void loop() {
+  WiFiClient client = server.available();   // listen for incoming clients
+
+  if (client) {                             // if you get a client,
+    Serial.println("New Client.");           // print a message out the serial port
+    String currentLine = "";                // make a String to hold incoming data from the client
+    while (client.connected()) {            // loop while the client's connected
+      if (client.available()) {             // if there's bytes to read from the client,
+        char c = client.read();             // read a byte, then
+        Serial.write(c);                    // print it out the serial monitor
+        if (c == '\n') {                    // if the byte is a newline character
+
+          // if the current line is blank, you got two newline characters in a row.
+          // that's the end of the client HTTP request, so send a response:
+          if (currentLine.length() == 0) {
+            // HTTP headers always start with a response code (e.g. HTTP/1.1 200 OK)
+            // and a content-type so the client knows what's coming, then a blank line:
+            client.println("HTTP/1.1 200 OK");
+            client.println("Content-type:text/html");
+            client.println();
+
+            // the content of the HTTP response follows the header:
+            client.print("Click <a href=\"/H\">here</a> to turn ON the LED.<br>");
+            client.print("Click <a href=\"/L\">here</a> to turn OFF the LED.<br>");
+
+            // The HTTP response ends with another blank line:
+            client.println();
+            // break out of the while loop:
+            break;
+          } else {    // if you got a newline, then clear currentLine:
+            currentLine = "";
+          }
+        } else if (c != '\r') {  // if you got anything else but a carriage return character,
+          currentLine += c;      // add it to the end of the currentLine
+        }
+
+        // Check to see if the client request was "GET /H" or "GET /L":
+        if (currentLine.endsWith("GET /H")) {
+          digitalWrite(LED_BUILTIN, HIGH);               // GET /H turns the LED on
+        }
+        if (currentLine.endsWith("GET /L")) {
+          digitalWrite(LED_BUILTIN, LOW);                // GET /L turns the LED off
+        }
+      }
+    }
+    // close the connection:
+    client.stop();
+    Serial.println("Client Disconnected.");
+  }
+}